【Product name】Dental Bonding System 6th Gen Self-Etching
【Specification】】Primer: 1.5mL/ 2.5mL/ 6mL/ bottle; Adhesive: 1.25mL/ 2.5mL, 5mL/ bottle
【Ingredients】 Dental Bonding System consists of primer and adhesive, the former is an orange liquid and the later a light yellow transparent solution, mainly composed of monomers such as Bis-GMA (Bisphenol A dimethacrylate), HEMA (2-hydroxyethyl methacrylate), dimethacrylate of ethylene glycol dimethyl ether, 10-methacryloyloxydecyl dihydrogen phosphate (MDP), and fillers like silica dioxide, camphorquinone, amine-based initiators,and coloring agents.
【Application】
● Tooth restoration
● Dental crown restoration
● Bondingfor light-cured composite resin fillings
● Cavity sealing
● Adhesive treatment for exposed tooth roots
● Other dental repair and crown restoratio nprocedures
【Applicable senarios】 Individuals who require adhesive restoration of enamel, dentin, and composite resin restoration.
【Certification】 ISO13485/ Free Sales Certificate
【Product properties】
● Self-etch bonding
● Selective-etch bonding of enamel
● Total-etch bonding
【Storage conditions】Store at temperatures between 2°C and 25°C. Do not expose to direct sunlight, strong light sources such as light-curing units, or close to heat sources.
【Service life】Unopened for 2 years, use out within one month after opening.
【Contraindications】
1. Discontinue use and seek immediate medical attention if there ar rashes, eczema, redness, ulcers, swelling, itching, numbness, or any allergic reactions after using this product.
2. Avoid contact with oral soft tissues, skin, and eyes. If contact occurs in the oral cavity or on the skin, wipe it off immediately with an alcohol swab and rinse with water. If it accidentally enters the eyes, rinse with a large amount of running water and seek medical attention from an ophthalmologist.
3. To prevent allergies from contact with the product, wear gloves and take appropriate protective measures. Avoid direct contact with uncured product.
【Special reminder】The light-curing device (lamp) should have a wavelength range of 400-515nm and a radiant intensity (light output) of no less than 120mw/cm2.
【Caution】
1. When dealing with pulp exposure or cases close to the pulp during cavity preparation, apply pulp protection.
2. Do not use eugenol-based materials for pulp protectio nor temporary sealing.
3. The use of hemostatic agents containing iron sulfate may result in brown lines at the neck of the tooth; Avoid using them in conjunction with this product.
4. This product is intended for use as a bonding agent for light-curing composite resins. Do not mix it with chemically cured composite resin bonding agents.
5. Do not ingest this product.
【Package】
Adhesive 1.5ml/ bottle 2.5ml/ bottle 5ml/ bottle | 2 bottles x 1 bag |  |
Primer 1.5ml/ bottle 2.5ml/ bottle 6ml/ bottle |
Curing time less than 12 seconds
【How to use】
1.Preparation of Cavities
For tooth decay, remove the decayed dentine, then clean and disinfect the cavity.
2. Moisture Control, Pulp Protection, Cavity Preparation
Carry out moisture-retaining treatment on the cleaned and disinfected cavity. If the dental pulp is exposed or the cavity is very close to the dental pulp, use calcium hydroxide to protect the pulp. Select the shade of light-curing composite resin as needed. For uncavitated enamel with adhered composite resin, apply phosphoric acid etchant to the uncavitated enamel around the cavity, rinse after 10 seconds, and dry.
3. Applying of Primer
Add an appropriate amount of primer to the mixing tank and use a small brush to apply it to the entire cavity surface.
4. Drying the primer
Use a gentle to moderate steam of air to dry the primer. Do not rinse after drying. Ensure that the primer is completely dried to maintain bond strength.
5. Applying of Dental Adhesive
Add an appropriate amount of adhesive to the mixing tank and use a small brush to apply it to the entire cavity surface. After application, gently air-blow the adhesive to create an uniform thin layer. Then, use the light-curing device to irradiate for 10 seconds to cure the adhesive.
6. Filling with Light-Cured Composite Resin
Fill the cavity with light-cured composite resin and cure it according to the specified time. After the curing is completed, perform the final grinding and polishing. When sealing the exposed root surface of the cavity and the indirect repaired cavity during the pre-treatment, and after the adhesive cures, a thin layer of low-viscosity light-cured composite resin should be applied on the tooth structure. Use the light-curing device for curing, and then wipe off the un-cured layer with an alcohol cotton swab.
7. Low-Viscosity Composite Resin
For the use of low-viscosity light-cured composite resin, please refer to the product instructions.
